You have no items in your shopping cart.
Products
- P1195 Mahindra Genio (BS III & BSIV)- Minimum rail pressure exceeded.
- P 0261 Mahindra Genio (BS III & BS IV) - Short circuit for injector 1
- P1196 Mahindra Genio (BS III & BSIV)- Maximum rail pressure exceeded.
- P1126 Mahindra Genio (BS III & BSIV)-Minimum temperature or temperature raise no reached within time limit.
- P1190 Mahindra Genio (BS III & BSIV)-Rail pressure raw value offset – above Max limit.
- P 0264 Mahindra Genio (BS III & BS IV) - Short circuit for injector 3.
- P1191 Mahindra Genio (BS III & BSIV)-Rail pressure raw value offset – below the Min limit.
- P1210 Mahindra Genio (BS III & BSIV)- Chip internal reset/clock loss/under voltage inside the ECU.
- U0073 Mahindra Genio (BS III & BS IV) - Can bus off error.
- P1250 Mahindra Genio (BS III & BSIV) - Open load.
- P1251 Mahindra Genio (BS III & BSIV) - Over temperature in the power stage of the ECU.
- P1252 Mahindra Genio (BS III & BSIV) - Short circuit to battery.
- P1192 Mahindra Genio (BS III & BSIV)- Maximum positive Rail pressure deviation exceeded.
- 804A /8045/1832 Mahindra Genio (BS III & BS IV) - Negative Acknowledgement / ECM Authentication Failed / Immobilizer Authentication Failed.
- P1193 Mahindra Genio (BS III & BSIV)- Maximum positive Rail pressure deviation exceeded concerning the set flow value.
- 8044 Mahindra Genio (BS III & BSIV)-No ECM Challenge.
- 1832/183F Mahindra Genio (BS III & BS IV) - Immobilizer Authentication Failed/ No ICU Response.
- 8048/8045/1832 Mahindra Genio (BS III & BSIV)-F() mismatch / ECM Authentication Failed / Immobilizer Authentication Failed
- 8049/8045/1832 Mahindra Genio (BS III & BSIV)-No ECMA acknowledgement / ECM Authentication Failed / Immobilizer Authentication Failed
- 8040/1832/183F Mahindra Genio (BS III & BS IV) - Transponder Missing-No Transponder/ Immobilizer Authentication Failed/ No ICU Response
- 8041/1832/183F Mahindra Genio (BS III & BS IV) - Invalid Transponder/ Immobilizer Authentication Failed / No ICU Response
- 8042/1832/183F Mahindra Genio (BS III & BS IV) - Wrong Transponder/ Immobilizer Authentication Failed/ No ICU Response.
- P0073 MahindraScorpio Vlx-Vls – EMS ECU in confirmed Mute error
- 8043/1832/183F Mahindra Genio (BS III & BS IV) - No Transponder is Learnt / Immobilizer Authentication Failed / No ICU Response.
- 8044/1832/183F Mahindra Genio (BS III & BS IV) - No ECM Challenge /Immobilizer Authentication Failed/ No ICU Response.
- P0102 Mahindra Scorpio Vlx-Vls - Voltage below lower Limit
- P0103 Mahindra Scorpio Vlx-Vls - Wrong crankshaft signal
- P1183 Mahindra Maxximo- Fuel temp above critical limit
- P0107 Mahindra Scorpio Vlx-Vls– Voltage below lowerlimit
- P0108 Mahindra Scorpio Vlx-Vls–Voltage above upperlimit
- P099B Mahindra Scorpio Vlx-Vls Automatic - Solenoid S7 Over Current.
- P0112 Mahindra Scorpio Vlx-Vls-Voltagebelow lower limit
- P0113 Mahindra Scorpio Vlx-Vls - Voltage above upper limit
- P0117 Mahindra Scorpio Vlx-Vls–Voltage below lower limit
- P0118 Mahindra Scorpio Vlx-Vls–Voltage above upperlimit
- P121A Mahindra Scorpio Vlx-Vls–Main relay does not open in time
- P121B Mahindra Scorpio Vlx-Vls–Main relay opens too early
- P099C Mahindra Scorpio Vlx-Vls Automatic - Solenoid S7 Low Current
- P0122 Mahindra Scorpio Vlx-Vls- Voltage below lowerlimit.
- P0123 Mahindra Scorpio Vlx-Vls- Voltage above upperlimit
- P099E Mahindra Scorpio Vlx-Vls Automatic - Solenoid S7 Low Current
- P160A MahindraScorpio Vlx-Vls – No load
- P1260 Mahindra Maxximo- Over temperature of pressure control valve power stage.
- P162B MahindraScorpio Vlx-Vls – EEPROM: error during last read operation.
- P162A MahindraScorpio Vlx-Vls – Communication error of CJ940.
- P161F Mahindra Scorpio Vlx-Vls–Below lower limit of enegising time- Injector # 3
- P099F Mahindra Scorpio Vlx-Vls Automatic - Solenoid S8 Low Current.
- P160E MahindraScorpio Vlx-Vls – No Load
- P160D MahindraScorpio Vlx-Vls – Short Circuit to Ground
- P160C MahindraScorpio Vlx-Vls – Short Circuit to Battery
