You have no items in your shopping cart.
Products
- P0501-64 TATA ACE : DFC for Plausibility defect for vehicle speed
- P0503-17 TATA ACE : DFC for Maximum threshold error for vehicle speed
- P0704-64 TATA ACE : DFC for Plausibility check for Clutch switch temp sensor
- P0655-98 TATA ACE : DFC for TTL over temperature error
- P0655-12 TATA ACE : DFC for TTL Short circuit to battery error
- P0655-11 TATA ACE : DFC for TTL Short circuit to ground error
- P0655-13 TATA ACE : DFC for TTL No load error
- P0217-98 TATA ACE : DFC for TTL over temperature error
- P160D-11 TATA ACE : DFC for TTL Short circuit to ground error
- P160E-12 TATA ACE : DFC for TTL Short circuit to battery error
- P072B-64 TATA ACE : DFC for Check for stuck Reverse Gear
- P0500-64 TATA ACE : DFC for Plausibility defect for vehicle speed
- P1836-64 TATA ACE : DFC for Check for stuck Reverse Gear
- P0500-17 TATA ACE : DFC for Maximum threshold error for vehicle speed
- P0685-11 TATA ACE : DFC for stuck main relay error
- P0685-15 TATA ACE : DFC for Early opening defect of main relay
- P062A-98 TATA ACE : DFC for Over temperature error on ECU power stage for Pre supply pump
- P060B-64 TATA ACE : DFC for Diagnostic fault check to report the NTP error in ADC monitoring
- P060B-91TATA ACE : DFC for Diagnostic fault check to report the ADC test error
- P0611-06 TATA ACE : DFC for Diagnostic fault check to report the error due to plausibility between the injection begin v/s injection type
- P0611-00 TATA ACE : DFC for Diagnostic fault check to report the plausibility error between level 1 energizing time and level 2 information
- P060B-62 TATA ACE : DFC for Diagnostic fault check to report the error in Voltage ratio in ADC monitoring
- P061B-48 TATA ACE : DFC for Diagnosis of lead path limitation forced by ECU monitoring level 2
- P0216-48 TATA ACE : DFC for Diagnostic fault check to report the error due to Over Run
- P061A-48 TATA ACE : DFC for Diagnosis of current path limitation forced by ECU monitoring level 2
- P1694-45 TATA ACE : DFC for DFC to set a torque limitation once an error is detected before MoCSOP's error reaction is set.
- P1607-62 TATA ACE : DFC for Diagnosis fault check to report the error to demand for an ICO due to an error in the PoI3 efficiency factor
- P1695-63 TATA ACE : DFC for Diagnosis fault check to report the error to demand for an ICO due to an error in the PoI2 shut-off
- P1607-64 TATA ACE : DFC for Diagnostic fault check to report the error due to injection quantity correction
- P0611-64 TATA ACE : DFC for Diagnostic fault check to report the error due to non plausibility in ZFC
- P1695-64 TATA ACE : DFC for Diagnosis fault check to report the demand for normal mode due to an error in the PoI2 quantity
- P1694-50 TATA ACE : DFC for Diagnostic fault check to report the timeout in the shut off path test
- P062B-64 TATA ACE : DFC for Diagnostic fault check to report the plausibility error in rail pressure monitoring
- P1694-63 TATA ACE : DFC for OS timeout in the shut off path test. Failure setting the alarm task period
- P1694-16 TATA ACE : DFC for Diagnostic fault check to report the error in under voltage monitoring.
- P0606-84 TATA ACE : DFC for Loss of synchronization sending bytes to the MM from CPU.
- P1694-48 TATA ACE : DFC for Diagnostic fault check to report that WDA is not working correct.
- P061C-61 TATA ACE : DFC for Diagnostic fault check to report the engine speed error
- P133D-48 TATA ACE : DFC for Diagnosis of current / lead path limitation forced by ECU monitoring level 2
- P1694-17 TATA ACE : DFC for Diagnostic fault check to report the error in overvoltage monitoring
- P061B-62 TATA ACE : DFC for Diagnostic fault check to report the error due to torque comparison
- P061A-40 TATA ACE : DFC for Diagnosis of set path limitation forced by ECU monitoring level 2
- P1694-57 TATA ACE : DFC for Diagnostic fault check to report that the positive test failed
- P268D-55 TATA ACE : DFC for check of missing injector adjustment value programming
- P1692-06 TATA ACE - DFC for Wrong set response time
- P268C-55 TATA ACE : DFC for check of missing injector adjustment value programming
- P0606-46 TATA ACE : DFC for Reported MSC-Errors of a R2S2
- P1327-64 TATA ACE : DFC for Diagnostic fault check to report the NTP error in ADC monitoring
- P1328-64 TATA ACE : DFC for Diagnostic fault check to report the ADC test error
- P1331-40 TATA ACE : DFC for DFC to set a torque limitation once an error is detected before MoCSOP's error reaction is set.
